詳細(xì)內(nèi)容：♂PC A786LONG TERM SUPPLY OF PC / / /ABS SHOW THE SUPERIOR PERFORMANCE OF THE NEW GENERATION OF PC AND /ABS. AT THE SAME TIME, THIS SERIES OF MATERIALS HAVE ALSO BEEN EVALUATED BY THE PUBLIC LABORATORY. AFTER 600H HYDROLYSIS AT 90 DEG C AT HIGH TEMPERATURE AND HUMIDITY AT 80%RH, THE NOTCHED IMPACT STRENGTH IS ONLY DECREASED BY 8.5%. AT PRESENT, THE MATERIAL HAS BEEN APPLIED IN THE MASS CHRYSLER LINGYU, 300C, BUICK AND OTHER MODELS. ULTRA LOW GLOSS PC "/ABS AUTOMOTIVE INTERIOR MATERIALS GENERALLY HAVE A MATTE, IT HELPS TO REDUCE THE VISUAL FATIGUE OF THE DRIVER, THEREBY IMPROVING THE DRIVING SAFETY. THE COMPREHENSIVE PERFORMANCE OF PC / / /ABS IS GOOD, BUT BECAUSE OF ITS HIGH SURFACE GLOSS, AND SPRAY MATTE PAINT TWO MATTE AND PROCESSING TO ACHIEVE THE AESTHETIC EFFECT. WITH THE INTRODUCTION OF AUTOMOBILE ELV REGULATIONS, THE ENVIRONMENTAL PROTECTION SOLUTION WITHOUT SPRAYING IS NEEDED TO REALIZE THE DIRECT RECYCLING OF THE PRODUCTS. THE SPRAYING FREE SOLUTION CAN NOT ONLY SUBSTANTIALLY REDUCE THE COST, BUT ALSO REDUCE THE ENVIRONMENTAL POLLUTION CAUSED BY THE SPRAYING PROCESS. EMA RESINS DO NOT RELEASE UNPLEASANT SUBSTANCES, SUCH AS HALOGENS, DURING INCINERATION. THE SURFACE TURBIDITY OF EMAC FILM IS HIGHER THAN THAT OF TYPICAL HOMOPOLYMER LDPE, WHICH IS SIMILAR TO THAT OF LATEX RUBBER AND MAKES IT SUITABLE FOR DISPOSABLE GLOVES AND SOME MEDICAL PRODUCTS. EMAC IS THE EXTRUSION COATING AND EXTRUSION LAMINATED RESIN IS GOOD. THIS IS BECAUSE IT HAS GOOD THERMAL STABILITY, NATURAL TO COMMON MATRIX ADHESION, FUSION AND RF WELDING PERFORMANCE, AND CAN BE PROCESSED IN DEVICE DESIGN OF LDPE. EMAC RESINS ARE COMMONLY EXTRUDED IN THE FORM OF RINGS AND FLAT FILM DIES TO FORM A HOT-MELT BONDING LAYER ON THE SUBSTRATE, OR AS A BOND LAYER FOR POLYOLEFIN, IONOMER, POLYESTER, CARBON, EVA, AND PVDC. EVA FOAM PRODUCTS: PRESSURIZED FOAMING, FOAM PLASTICS, SLIPPERS, SANDALS, BUILDING MATERIALS, ETC.. INJECTION MOLDING FOAM HAS A VARIETY OF INDUSTRIAL COMPONENTS, WOMEN'S SOLES, HOT MELT ADHESIVES. ETHYLENE VINYL ACETATE COPOLYMER MOLDING PROCESSING OF EVA INJECTION MOLDING, EXTRUSION, BLOW MOLDING, CALENDERING, ROTATIONAL MOLDING, FOAM, VACUUM COATING, HEAT SEALING, WELDING AND OTHER PROCESSING. EVA, 007S, EVA 0270, EVA 1810, EVA 230, EVA 260, EVA 265, EVA 2815, EVA, 3107AC, EVA 3150, EVA, EVA 3176, EVA 3185, AND C 360 IN ADDITION TO THE SPECIAL GRADE ABS RESIN OR RESIN COLORING TREATMENT, MOSTLY PALE IVORY OR PORCELAIN WHITE OPAQUE PARTICLES. RESIN WATER ABSORPTION IS NOT VERY HIGH, SUCH AS THE PROCESSING PERMIT VALUE OF 0.1 - 0_2% BELOW, FOR THE TIGHT PACKAGING, STORAGE PROPERLY, AND PRODUCTS ARE NOT TOO HIGH REQUIREMENTS, CAN BE WITHOUT DRYING TREATMENT CAN BE PROCESSED. BUT IF THE MOISTURE CONTENT OF PARTICLES IN THE SPECIFIED VALUE, MUST BE DRIED BEFORE MOLDING, THE HIGHER REQUIREMENTS FOR THE SPECIAL GRADE PARTICLES OR PRODUCTS (SUCH AS ELECTROPLATING PRODUCTS), IN MOLDING MUST BE DRIED BEFORE. ABS 700, ABS 900, ABS 920, ABS 600, ABS 100, ABS 300, ABS 400, ABS 180, ABS 500, ABS, ABS 560, AND C 532. PBT, VLAN-XC AND PBT ARE TWO COMPETING TECHNOLOGIES, BOTH FROM THE STANDARDIZATION DRIVE OR FROM THE POINT OF VIEW OF THE CE SOLUTION. PBT TECHNOLOGY IS SUPERIOR TO VLAN-XC IN ITS COMPATIBILITY WITH TRADITIONAL ETHERNET, INTEROPERABILITY AND STANDARDIZATION WITH OTHER NETWORK TECHNOLOGIES. T-MPLS HAS TAKEN THE LEAD IN THE STANDARDIZATION PROCESS, AND THE FUTURE IS LIKELY TO BE A COMPETITION BETWEEN PBT AND TMPLS IN TERMS OF COST. AT PRESENT, OPERATORS AT HOME AND ABROAD ARE EVALUATING PBT/PBB TECHNOLOGY. ALTHOUGH PBT LACKS A VALID AUTOMATIC CONFIGURATION SYSTEM THAT CAN AFFECT ITS SCALABILITY, VENDORS DO NOT QUESTION THE ABILITY OF PBT TO PROVIDE AN EFFICIENT, CONNECTION ORIENTED, PACKET BASED NETWORK. SOME PEOPLE WHO DO NOT SUPPORT PBT TECHNOLOGY BELIEVE THAT PBT DOES NOT HAVE THE ABILITY TO POINT TO MULTIPOINT. BUT IN ACTUAL NETWORKING, PBT, TV4264SN, PBT, TV4270, PBT, TV4290, PBT, TV6220, PBT, TV6240, PBT, TV6241SN, PBT, TV6241T.